Search results

Bump for a great projector kit!

did you tighten the back nut that holds the projector? if the projector is tightly installed, then what you are seeing is the actual bike bouncing and thus the light is also bouncing. with a stock headlight there is no cut off line, so you dont see the light move around as you ride. with a...

mailing out a new plug tomorrow.

the bulb should fit, there is a square notch that needs to line up. if you can email me a picture of the bulb and how it fits. [email protected] also email your order info and ill mail you a new h4 plug tomorrow.

Which bulb doesnt fit right? the hid bulb that goes into the projector? if that H4 pigtail is missing from your order, email bkmoto for a new one. [email protected]

I spoke to you on the phone a few days ago, we resolved this issue, you were not inserting the bulb correctly.

very nice! i like the blacked out look!!

take a hair drier, heat up that glue spot, it will come off easier once hot. But its not easy removing that glue from delicate chrome surfaces, also try so use some goo gone, it usually helps remove glue pretty well.

connect the red/black wires from the halo inverter directly to the battery and see if the halo is coming on. if not your halo or inverter might be broken, so contact bkmoto for a replacement.

The pojector shroud is removable, so its very easy to paint. I might make a tutorial for the fz6 and fz8 fazer soon, I already have all the pictures, just need to find time to type it up.

Installation instructions posted! I posted complete installation instructions in the how-to section. http://www.779cc.org/forum/how-tos/1460-how-install-bkmoto-fz8-fz6r-hid-bixenon-projectors-angel-demon-eye.html

reserved 2

The rubber dust caps need to be slightly modified to fit the new hid bulb rubber seal. Cut off this piece put the light bulb in the projector. Bulb, silicone spacer, metal ring, then the rear nut. fish all the wires through the light bulb grommet, insert grommet into rubber dust cap...

We are now ready to mount the projector. Remove all hardware from the projector, except the silicone washer. You will need to modify the H4 adapter plate slightly, and shave off the orientation tab. You can thank Yamaha for that, as they designed the headlight with the whole H4 base slightly...

This post will show all the steps required to properly install bkmoto.com HID projector headlight kit into the 2008+ Yamaha FZ8 FZ8-N This kit will also work on the FZ6R, as the headlight is the same as the FZ8. More information on this kit can be found on www.bkmoto.com The kit will come...

His ballast is under the air box, where the stock intake snorkel used to be with the wires coming out front the side of the frame. also make sure you shave off the little orientation tab on the H4 adapter plate, as the way the headlight is designed it will sit at an angle and the light will...

You still need to open the headlight and separate the lens, what they mean is that normally in projector installs you need to make modofications to the reflector to mount the projector, with this kit the projector simply bolts on to the reflector with no modifications, you just insert it into...

Curious to see the green halo and blue demon. post some pictures when you have them installed :D

First bike, 2003 Kawasaki zx6r 636. cool looking bike, but SUPER uncomfortable, and harsh suspension. 2001 F4i, great bike, the most comfortable supersport our there. 1999 Ninja 500 super comfy, but ancient technology. 2008 DRZ400SM. Hands down the most fun bike i've ever owned...

This is a bixenon projector, it does both low beam and high beam, using your factory switch, same as stock. The low beam has a sharp cut off line so it doesnt shine high enough to blind oncoming traffic, high beam works instantly and opens up the beam to shine higher for high beam.